Showing results: 226 - 240 of 608 items found.
-
Panther4HT Master- Slave DSU -
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
63200E Series -
Chroma ATE Inc.
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
FIXUROOF 1000 -
Com-Ten Industries
The Fixuroof 1000 portable pull-tester is an accurate unit, designed for testing in the field the pull-out force for base ply fastener. Easily determine whether the mechanical fastener provides sufficient resistance to static uplift force to meet the wind load requirements.
-
CTS-02V4 -
Nitto Construction Inc.
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
Blonder Tongue Laboratories, Inc.
Tools to assist in video delivery installations, Blonder Tongue’s collection of Test & Measurement handheld products are second to none in capturing data for troubleshooting and testing purposes. These units provide real-time spectrum analysis, making them invaluable to those in the field.
-
M+P International
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
Cincinnati Test Systems
Pressure decay leak testing technology has become a mainstay in the arena of high volume production testing. Pressure decay testing methods offer the world's manufacturers a cost-effective and easily applicable solution to the leak testing challenges they encounter on a given day. Fundamentally, pressure decay testing is a straightforward measurement technique; Cincinnati Test Systems (CTS) pioneers new and innovative ways to integrate our technology into custom turnkey systems that exceed the industry standards for reliability and repeatability. CTS' 30+ years of experience goes way beyond the pressure test unit by offering our customers comprehensive, custom turnkey solutions to the most challenging leak testing problems.
-
AC-LB-Series -
Eagle Eye Power Solutions
Eagle Eye AC Load Banks are commonly used for testing generator sets, UPS units, aircraft power inverters and other government and military AC power sources. The Eagle Eye AC LB-Series is the smallest in the industry and offers unmatched durability in even the harshest testing environments. Eagle Eye offers several standard models as well as custom AC Load Banks.
-
Cincinnati Sub-Zero Products
CSZ''s Welded Walk-In chambers are ideal for applications that require high temperature testing over 93C (200F), high humidity, rapid temperature change rates, or combined environmental testing with altitude simulation. These chambers are constructed as one piece and are welded to form a hermetically sealed unit around a structural steel frame or they can also be built in sections based on move-in restrictions.
-
Eclypse International
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
165 CB -
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
458-3SLB -
Telebyte, Inc.
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
MTI Corp.
thermal test chamber from -40°C to +100°C with a programmable temperature controller and an accuracy of ±1°C. With a chamber size of 470 L x 420W x 460H mm (80L), it becomes a cost-effective testing unit for rechargeable batteries.
-
Fiber Lab 250 -
M2 Optics, Inc.
Fiber Lab 250 from M2 Optics provides an ideal platform for testing optical equipment requiring short distances of fiber, such as latency or high bandwidth multimode applications. A rack-mountable unit, it offers fiber protection and an easy interface for various equipment.
-
Triad RF Systems, Inc.
This lab unit is capable of a power output of 30 Watts and operates at a frequency range from 1200 MHz to 1400 MHz. The compact and rugged design of this system is ideal for bench-top testing and many other applications where both simplicity and portability are required.
